DIY Bar Stools with Metal Bar Accents
Hi, it’s Amy from Hertoolbelt back with another build project for you. Since we have the perfect corbel for your kitchen island, we better build some easy bar stools too. The inspiration for the bar stool design is from Better Homes and Gardens. I love the bright pop of color in the white kitchen, stunning!
(Note: this picture is the inspiration not the actual build)
We are going to simplify the bar stools by removing the flair in the legs, and these stools become a super easy DIY and very inexpensive. The plans are for a 24″ bar stool, if you need a taller version, just add length to the legs.
How to Build a Bar Stool
Click Here to Get a Free Printable Version of This Building Plan
*All Remodelaholic building plans and tutorials are for personal, non-commercial use only. Use this printable plan as you build, but don’t sell the PDF plan or otherwise distribute the file. (Items built following this tutorial may be sold, but the instructions and PDF file may not.) Thanks!
Materials Needed
- 1 – 2″ x 2″ x 8′ board
- 1 – 1″ x 2″ x 8′ board
- 1 – 1″ x 4″ x 8′ board or 15″ x 15″ of 3/4″ plywood
- 1/2″ metallic tube conduit
- 1 1/4″ pocket screws
- wood glue
- wood filler
- sand paper
- primer and paint
Cut List
| Quantity | Length | Width | Thickness | Material |
| 4 | 23 1/4″ | 1 1/2″ | 1 1/2″ | 2×2 |
| 6 | 10″ | 1 1/2″ | 3/4″ | 1×2 |
| 1 | 10 3/4″ | 1 1/2″ | 3/4″ | 1/2 |
| 2 | 11″ | 1/2″ diam | 1/2″ metal conduit | |
| 5 | 15″ | 3″ | 3/4″ | 1×4* |
*can be replaced with 15″ x 15″ x 3/4″ plywood or any material.
Step 1
Cut 6 pieces of the 1 x 2 that are 10″ x 1 1/2″ x 3/4″. Cut 1 piece that is 10 3/4″ x 1 1/2″ x 3/4″. Use a pocket jig and make pocket holes in each end of the back face of all 7 pieces. Cut 4 legs 23 1/4″ x 1 1/2″ x 1 1/2″.
Use wood glue and 1 1/4″ pocket screws to assemble the back legs. Attach one of the 10″ pieces flush with the top and a second 10″ piece 7 1/2″ from the bottom, centering on the leg width.
 |
 |
Attach 2 10″ pieces for the sides flush with the top, again centered on the leg width. Attach the 10 3/4″ piece in the center of the lower back piece.
Step 2
Cut 2 pieces of 1/2″ conduit to about 11″. You can easily cut metal conduit with a hack saw or a grinder with a cut off wheel. 1/2″ conduit has an inside diameter of 1/2″ and the outside is just under 3/4″ diameter. In both front legs, drill 3/4″ holes about 1/2″ deep – 6 1/4″ from the top and 9 1/2″ from the bottom, centered on the leg width.
Use wood glue and 1 1/4″ pocket screws to assemble the front legs. Attach one of the 10″ pieces flush with the top and a second 10″ piece 7 1/2″ from the bottom, centering on the leg width.
Insert the 2 conduit pieces in the holes and attach the other leg. If you are planning on painting the conduit, it may be easier to paint it before installing.
Attach the front legs to the back legs and sides, again with wood glue and 1 1/4″ screws. Add pocket holes to the upper 10″ pieces to attach the seat later.
Step 3
If you are using the 1×4 for the seat, cut the 1×4 into5 – 15″ lengths. Trim the long edges to make sure they are straight. Join the boards with wood glue and pocket holes and screws, or your preferred method. Let the glue dry, then sand smooth. Cut the board down to 15″ x 15″. If you want, add a 30 deg chamfer on the bottom of the seat.
If you would like to add a ‘handle’. Mark the center line of the seat and drill 2 – 1″ diameter holes about 6″ apart and 4 9/16″ from one side. Use a jig saw or similar to cut a straight line connecting the tops and bottoms of both circles.
Center the seat on the leg/base and attach the seat with wood glue and 1 1/4″ pocket screws.
Note: the handle and conduit are totally optional and purely for looks.
Step 4
Remove any excess glue, apply wood filler to nail holes, cracks and blemishes and allow to dry. Sand the wood filler and bar stool until smooth finishing with 120-150 grit sand paper. Stain or paint and prime as you like.
Here is my finished bar stool. I painted the conduit Rustoleum Anodized Bronze and the wood Rustoleum Robins Egg.
Cost Breakdown – according to my local Home Depot
- 2″ x 2″ x 8′ board – $1.99
- 1″ x 2″ x 8′ board – $1.07
- 1″ x 4″ x 8′ board – $2.18
- 1/2″ x 10′ electric metal conduit – $2.48 (enough for 5 bar stools)
- Total – $7.72 + paint or stain
———————————————
Itching to build something else? Try our other building plans such as:
Wall-Mount Dry Erase Message Board
Amy is the tool lover at Hertoolbelt. On Hertoolbelt, Amy shares DIY furniture plans, handyman tutorials, and craft patterns. She has three pint sized 'helpers' that help fix things around the house and build fun projects.
I love the bar stools especially since you painted them red (my favorite color). It’s hard finding bar stools that fit the criteria of your kitchen. Thanks for the plans 🙂
The pictures of the red stools shows the legs at an angle & not perpendicular to the top. The top cross pieces would have to be shorter than the bottom cross pieces, longer than 10″.
(Note: this picture is the inspiration not the actual build)
Yes, thanks, Ed! Jack, you are absolutely correct, but we simplified it and made the legs straight to make them easier to build. Thanks for the comment!
I love these Amy!! You are so talented. Would you (or Cassity) mind if I used an image from this post and put it in a little round up I’m doing? Thank girls <3